MODEL NO. GL100D
   
     Straight body type                  Angle body type
When water level rises to top height, water level in small water tank slowly declines as users consume water from it. When water level declines to a preset level,  this valve will open to fill water into the small tank.
It helps to prevent whirlpool and avoids mechanical problems from too frequent on&off movement if valve opens whenever level declines just a little.Â
Â
| Body &Â Bonnet | Cast iron, Ductile iron, Cast steel, Stainless steel etc |
| Stem | Stainless steel |
| Disc | Brass, Carbon steel, Ductile iron etc |
| Seat | Brass, Stainless steel, Carbon steel etc |
| Sealing | NBR, EPDM etc |
| Diaphragm | NBR, EPDM etc |
| Flange Dimension | ASME B16.42, BS4504, ISO2531, ISO7005 etc. |
| Face to Face Length | ANSI B16.10,BS5155, ISO5752, DIN3352 etc. |
KARFAR competitive advantages:
*Well and high Quality Control
*Prompt Delivery
*Customer's Designs and Logos are welcome
*Competitive Price
*Small order Acceptable
 Fixed Water Level Control Altitude Valve
MODEL NO. GL100D
        Straight body type                  Angle body type
When water level rises to top height, water level in small water tank slowly declines as users consume water from it. When water level declines to a preset level,  this valve will open to fill water into the small tank.
It helps to prevent whirlpool and avoids mechanical problems from too frequent on&off movement if valve opens whenever level declines just a little.Â
Â
| Body &Â Bonnet | Cast iron, Ductile iron, Cast steel, Stainless steel etc |
| Stem | Stainless steel |
| Disc | Brass, Carbon steel, Ductile iron etc |
| Seat | Brass, Stainless steel, Carbon steel etc |
| Sealing | NBR, EPDM etc |
| Diaphragm | NBR, EPDM etc |
| Flange Dimension | ASME B16.42, BS4504, ISO2531, ISO7005 etc. |
| Face to Face Length | ANSI B16.10,BS5155, ISO5752, DIN3352 etc. |
KARFAR competitive advantages:
*Well and high Quality Control
*Prompt Delivery
*Customer's Designs and Logos are welcome
*Competitive Price
*Small order Acceptable
Â
The forced circulation pump does not rely on the centrifugal force of the impeller to the liquid, but uses the thrust of the rotating impeller blades to make the sent liquid flow along the direction of the pump axis. When the pump shaft is driven by the motor to rotate, because the blade has a certain helix angle with the axis of the pump shaft, a thrust (or lift) is generated on the liquid, and the liquid is pushed out and discharged along the discharge pipe. When the liquid is pushed out, a partial vacuum is formed at the original position, and the liquid outside will be sucked into the impeller along the inlet pipe under the action of atmospheric pressure. As long as the impeller keeps rotating, the pump can continuously suck in and discharge liquid. The forced circulation pump works by using the horizontal thrust along the direction of the pump axis generated by the rotation of the impeller, so it is also called a horizontal axial flow pump. Mainly used in the evaporation of diaphragm method caustic soda, phosphoric acid, vacuum salt production, lactic acid, calcium lactate, alumina, titanium dioxide, calcium chloride, ammonium chloride, sodium chlorate, sugar, molten salt, paper, waste water and other industries. Concentration and cooling, in order to improve the production capacity of the equipment, increase the heat transfer coefficient of the heat exchanger for forced circulation. Therefore, it can also be called an axial flow evaporative circulation pump.
Forced Circulation Pump,Circulation Pump,Recirculating Pump,Centrifugal Pumps
Jiangsu Qiantu Trading Co., Ltd. , https://www.qiantupump.com