Selection and use of small pumps

In recent years, the social ownership of agricultural pumps in our country has increased greatly, especially small agricultural pumps represented by submersible pumps and self-priming pumps are favored by the majority of users because of their low prices and easy operation. However, due to the large number of small pump manufacturers, technical strength varies greatly, resulting in poor product quality advantages and disadvantages. Coupled with the operation, improper use and other factors, so many users have a new set of troubles, or even a lot of economic losses. According to statistics, at present, half of the annual production of agricultural pumps in China is used to replace scrapped products. Therefore, how to choose a long-lasting, pleasing pump and how to extend the life of the pump has become a great concern to the majority of users.

First, choose a standard pump

1, what is the standard pump?

Standardization of the pump is the state according to the requirements of ISO, development, implementation of the latest models of pumps. Its main features are small size, light weight, excellent performance, easy operation, long life, low energy consumption. It represents the latest trend of the current pump industry.

2, how to choose the pump

Users choose the pump, it is best to the agricultural machinery department approved point of sale, we must recognize that the manufacturer. It is recommended to give priority to the purchase of water-filled submersible pumps, and to see the grades and product quality certification. Do not buy "three no" (that is, no manufacturer, no production date, no production license) products, otherwise there is a problem, the user will do nothing.

3, what brand of water pump is good

As a user, due to the limitations of professional knowledge, it is difficult to decide, the best way is to consult the pump experts. If you really no one consulting, may wish to consult some of the older pump users, especially those who are close to their own conditions, to buy these users reliable, reliable and more mature products, after all, a wise choice. At the same time, should be based on the local power supply situation to decide with single-phase pump or three-phase pump.

Second, choose to meet the lift requirements of the pump

1, pump head choice

The so-called head lift is the required lift, not the lift height, a clear choice of pump is particularly important. Pump lift about 1.15 to 1.20 times the height of the lift. If a water source to the water vertical height of 20 meters, its required lift is about 23 to 24 meters. Select the pump should make the best lift on the pump nameplate and the required head close, in this case, the highest efficiency of the pump, the use of more economical. However, it is not absolutely necessary that the pump should be absolutely energy-efficient. As long as the average deviation does not exceed 20%, the pump can work under more energy-efficient conditions.

2, how much the nameplate lift as well

Choose a nameplate pump far less than the required head of a pump, often can not meet the user's wishes, even if it is pumping water, the water will be pitifully small, and even become a useless "free pump" . Whether to buy the pump lift the higher the better? actually not. High-lift pump for low lift, there will be excessive flow, resulting in motor overload, if the long run, the motor temperature, the winding insulation will gradually aging, or even burn the motor.

Third, choose the right flow pump

Pump flow, that is, the amount of water generally should not choose too large, otherwise, will increase the cost of purchasing a pump. Specific issues should be specific analysis, such as users own draft self-priming pump, the flow should be selected smaller; such as user irrigation submersible pump, you can choose the appropriate flow larger.

Fourth, the use should pay attention to several issues

Correct use of the method is to extend the pump life, an important factor in reducing economic losses.

1, for the submersible pump

Before starting to do some necessary checks: the rotation of the pump shaft is normal, with or without stuck phenomenon; impeller position is normal; cable and cable plug without rupture, abrasions and broken phenomenon. Operation should pay attention to observe the voltage changes, the general control of the rated voltage within ± 5%. In addition, the location of the pump in the water is very important, should be selected as much as possible in the water volume, non-silt, good water quality, vertical suspension in the water, not allowed to cross, so as not to fall into the mud or suspended matter blocked by the pump imports, and Lead to a sharp drop in water or pumping to the water.

2, for self-priming pump

Should be placed in a well ventilated place to run, in order to facilitate rapid cooling, reduce motor temperature. Otherwise, prolonged operation, easy to burn the motor. If a farmer is using a self-priming pump, the motor is overheated and the coil burned out because the plastic film covering the motor is not removed. In addition, before starting, be sure to check the pump body of water, otherwise, not only affect the self-priming performance, but also easy to burn shaft seal components. Under normal circumstances, the pump should start 3 to 5 minutes after the water, or should immediately stop checking.

3, pump maintenance

Once the pump fails, should not disassemble yourself. Because of their demolition, I do not know where the fault is caused by blindly dismantling a pass; Second, there is no special tools and often damage the original parts intact. The best way is to have the experience, the maintenance of scale maintenance, and timely replacement of "over age" parts and some wearing parts. Under normal circumstances, the pump should be repaired once every six months, to eliminate "sick" work.

4, non-use of storage

In the non-use period, the pump should be promptly removed from the water, and emptying the pump water, especially in the cold winter. Then place it in a dry place, conditional users can also apply butter in the key parts of the pump, add lubricant to the bearings to prevent corrosion of parts. In addition, the non-use of the pump, not the longer the better. If you do not use for a long time, not only easy to rust parts, but also reduce the service life of the pump.

Sample Preparation Equipment

Sample Preparation Equipment,Solid Particles Grinding,Solid Particles Grinding Ball Mills,Laboratory Use Ball Mills

Shaoxing Dongjing Machinery Instrument Equipment Co.,Ltd. , https://www.sxdj-machine.com

Posted on