Â
Main features:
 HTC400DF truck mounted drilling rig is a directly rotary drilling rig. This truck chassis could be adopt the 6×4 special chassis of brand SINOTRUK, FAW, DONGFENG, 11.00R20 steel off-road tire tread, with good off-road performance.
This rig has very compact structure, the engine of chassis could be adopted 180hp,210hp,240hp,270hp,290hp diesel engine, the engine is made by SINOTRUK,FAW,DONGFENG. The drilling rig has independent diesel engine (FAW DEUTZ-WP6G125E22), the power is 92kw. Not only meet the drilling requirements, but also reduce energy consumption, it is very affordable.
This rig is design principle is an advanced hydraulic cylinder for drilling, stepless lift, it can be achieved automaic drilling. it can automatically adjust the drilling speed for different geological conditions.
The drilling process can be achieved in pressruized drilling technology, adjust different pressure for different geological conditions, and can be viewed drilling pressure by pressure gauge. At the same time, it can adjust the drilling speed.
The drilling rig can achieved fast drilling by manually, especially for soil. It can achieved different speed for different soil.
It has a large lifting force hydraulic main hoist, stepless lift, and to achieve release rope quickly. When upgrading heavy, the lifting speed need slow to aviod crash the turntable and wellhead board. When put down single drill pipe, operate the quick handle, it can achieved release rope quickly like mechanical hoist.
It has a hydraulic tool hoist, the tool hoist has large lifting force and quick lifting speed, it is both easy to loading drill tools, drill pipe and drill accessories transport, and can slide up and down with anchors, its very convenient to load and unload the drill pipe.Â
It has a hydraulic cylinder control double card board forward and backward, it makes the insurance card board closed, to achieve stuck or release the pipe joints.
It use integrated design of pneumatic, to achieve the BW850/2A mud pump clutch using pneumatic remote control, it has high degree of automation and easy-saving operation.
It is installed 4 hydraulic legs and 2 mechanical legs, every hydraulic leg rod with locknut. After leveling the rig, it can lock the cylinder  use locknut. So, even if the cylinder leaks, the chassis is not instability.
The turntable use stir bars, internal turntable use spiral arc gear to transmission, it has large torque, it about 2 times of similar products at domestic and foreign.
It is installed a generator (30kw) , so that it is convenient to illuminate or work at night.
The hydraulic system use open system, the chassis and drilling rig are separately manipulated, it can avoid misuse. Winter oil heater and summer oil radiator are installed, to adapt to different seasons hydraulic oil for heating and cooling.
This drilling rig equipped with an auxiliary unloading cylinder, it can be used to promote the turntable ratchet, to achieve auxiliary unloading the drill pipe.
Â
Technical parameter | |||
Drilling depth(M) |
400 |
||
Drilling diameter(mm) |
500 |
||
Speed of turntable(r/min) |
117;102;60;38;23;13;16(reverse) |
||
Torque of turntable(KN.m) |
5.4---50(reverse) |
||
Single rope lifting capacity of main windlass(KN) |
45 |
||
The capacity of main windlass(KN) |
270 |
||
Single rope lifting capacity of tool windlass(KN) |
20 |
||
 The rope capacity of tool windlass(m) |
40 |
||
 The lifting capacity of hook(KN) |
270 |
||
 Bearing capacity of mast (KN) |
270 |
||
 The height of mast (mm) |
12500 |
||
 Bearing capacity (t) |
36 |
||
Pipe |
Kelly (mm) |
108×108×7500 |
|
 Assistant pipe (mm) |
Ф89×10×5500 |
||
Hydraulic pump |
Pump delivery (ml/r) |
50/32 |
|
 Rated speed (r/min) |
2000 |
||
 Rated pressure(MPa) |
20 |
||
Diameter of cylinder (mm) |
150 |
||
 Stroke of piston (mm) |
180 |
||
|
BW850/2A plunger pump |
Theory of flow (L / min) |
600Â Â Â Â Â 850 |
|
Rated pressure (Mpa) |
3Â Â Â Â Â Â Â Â 2 |
||
Pounding  times (min-1) |
58Â Â Â Â Â Â Â 82 |
||
 Diameter of suction tube (mm) |
127 |
||
 Diameter of drain pipe (mm) |
64 |
||
 Input speed (r / min) |
470 |
||
 Input power (kw) |
40 |
||
 Overall dimensions (mm) |
2000*1030*1400 |
||
Weight (t) |
1.5 |
||
Truck chassis |
Model |
SINOTRUK |
|
 Drive form |
6×4 |
||
Engine |
 Model |
CA6110-125,WD615.96E,YC190Â diesel engine |
|
 Rated power(HP) |
180,266,190 |
||
 Speed (r/min) |
2300 |
||
Size (L*W*H)(mm) |
10198×2490×2980 |
||
Electric generator |
Model |
MF |
|
Rated power (kw) |
30 |
||
Rated voltage(v) |
400 |
||
Rated current(A) |
27 |
||
Speed (r/min) |
1500 |
||
Frequency(Hz) |
50 |
||
Protection level |
IP21 |
||
Insulation Class |
H |
||
The best working gear (or speed) |
5th gear(1000-1400r/min) |
||
The highest speed(Km/h) |
70 |
||
 Weight (kg) |
21650 |
||
Transport size(L*W*H)(mm) |
12740×2490×4210 |
||
Working size(L*W*H)(mm) |
10780×3040×13800 |
||
Â
Main features:
 HTC400DF truck mounted drilling rig is a directly rotary drilling rig. This truck chassis could be adopt the 6×4 special chassis of brand SINOTRUK, FAW, DONGFENG, 11.00R20 steel off-road tire tread, with good off-road performance.
This rig has very compact structure, the engine of chassis could be adopted 180hp,210hp,240hp,270hp,290hp diesel engine, the engine is made by SINOTRUK,FAW,DONGFENG. The drilling rig has independent diesel engine (FAW DEUTZ-WP6G125E22), the power is 92kw. Not only meet the drilling requirements, but also reduce energy consumption, it is very affordable.
This rig is design principle is an advanced hydraulic cylinder for drilling, stepless lift, it can be achieved automaic drilling. it can automatically adjust the drilling speed for different geological conditions.
The drilling process can be achieved in pressruized drilling technology, adjust different pressure for different geological conditions, and can be viewed drilling pressure by pressure gauge. At the same time, it can adjust the drilling speed.
The drilling rig can achieved fast drilling by manually, especially for soil. It can achieved different speed for different soil.
It has a large lifting force hydraulic main hoist, stepless lift, and to achieve release rope quickly. When upgrading heavy, the lifting speed need slow to aviod crash the turntable and wellhead board. When put down single drill pipe, operate the quick handle, it can achieved release rope quickly like mechanical hoist.
It has a hydraulic tool hoist, the tool hoist has large lifting force and quick lifting speed, it is both easy to loading drill tools, drill pipe and drill accessories transport, and can slide up and down with anchors, its very convenient to load and unload the drill pipe.Â
It has a hydraulic cylinder control double card board forward and backward, it makes the insurance card board closed, to achieve stuck or release the pipe joints.
It use integrated design of pneumatic, to achieve the BW850/2A mud pump clutch using pneumatic remote control, it has high degree of automation and easy-saving operation.
It is installed 4 hydraulic legs and 2 mechanical legs, every hydraulic leg rod with locknut. After leveling the rig, it can lock the cylinder  use locknut. So, even if the cylinder leaks, the chassis is not instability.
The turntable use stir bars, internal turntable use spiral arc gear to transmission, it has large torque, it about 2 times of similar products at domestic and foreign.
It is installed a generator (30kw) , so that it is convenient to illuminate or work at night.
The hydraulic system use open system, the chassis and drilling rig are separately manipulated, it can avoid misuse. Winter oil heater and summer oil radiator are installed, to adapt to different seasons hydraulic oil for heating and cooling.
This drilling rig equipped with an auxiliary unloading cylinder, it can be used to promote the turntable ratchet, to achieve auxiliary unloading the drill pipe.
Â
Technical parameter | ||||||||||||||||||||||||||||||||||||||||||||
Drilling depth(M) |
400 |
|||||||||||||||||||||||||||||||||||||||||||
Drilling diameter(mm) |
500 |
|||||||||||||||||||||||||||||||||||||||||||
Speed of turntable(r/min) |
117;102;60;38;23;13;16(reverse) |
|||||||||||||||||||||||||||||||||||||||||||
Torque of turntable(KN.m) |
5.4---50(reverse) |
|||||||||||||||||||||||||||||||||||||||||||
Single rope lifting capacity of main windlass(KN) |
45 |
|||||||||||||||||||||||||||||||||||||||||||
The capacity of main windlass(KN) |
270 |
|||||||||||||||||||||||||||||||||||||||||||
Single rope lifting capacity of tool windlass(KN) |
20 |
|||||||||||||||||||||||||||||||||||||||||||
 The rope capacity of tool windlass(m) |
40 |
|||||||||||||||||||||||||||||||||||||||||||
 The lifting capacity of hook(KN) |
270 |
|||||||||||||||||||||||||||||||||||||||||||
 Bearing capacity of mast (KN) |
270 |
|||||||||||||||||||||||||||||||||||||||||||
 The height of mast (mm) |
12500 |
|||||||||||||||||||||||||||||||||||||||||||
 Bearing capacity (t) |
36 |
|||||||||||||||||||||||||||||||||||||||||||
Pipe |
Kelly (mm) |
108×108×7500 |
||||||||||||||||||||||||||||||||||||||||||
 Assistant pipe (mm) |
Ф89×10×5500 |
|||||||||||||||||||||||||||||||||||||||||||
Hydraulic pump |
Pump delivery (ml/r) |
50/32 |
||||||||||||||||||||||||||||||||||||||||||
 Rated speed (r/min) |
2000 |
|||||||||||||||||||||||||||||||||||||||||||
 Rated pressure(MPa) |
20 |
|||||||||||||||||||||||||||||||||||||||||||
Diameter of cylinder (mm) |
150 |
|||||||||||||||||||||||||||||||||||||||||||
 Stroke of piston (mm) |
180 |
|||||||||||||||||||||||||||||||||||||||||||
|
BW850/2A plunger pump |
Theory of flow (L / min) |
600Â Â Â Â Â 850 |
||||||||||||||||||||||||||||||||||||||||||
Rated pressure (Mpa) |
3Â Â Â Â Â Â Â Â 2 |
|||||||||||||||||||||||||||||||||||||||||||
Pounding  times (min-1) |
58Â Â Â Â Â Â Â 82 |
|||||||||||||||||||||||||||||||||||||||||||
 Diameter of suction tube (mm) |
127 |
|||||||||||||||||||||||||||||||||||||||||||
 Diameter of drain pipe (mm) |
64 |
|||||||||||||||||||||||||||||||||||||||||||
 Input speed (r / min) |
470 |
|||||||||||||||||||||||||||||||||||||||||||
 Input power (kw) |
40 |
|||||||||||||||||||||||||||||||||||||||||||
 Overall dimensions (mm) |
2000*1030*1400 |
|||||||||||||||||||||||||||||||||||||||||||
Weight (t) |
1.5 |
|||||||||||||||||||||||||||||||||||||||||||
Truck chassis |
Model |
SINOTRUK |
||||||||||||||||||||||||||||||||||||||||||
 Drive form |
6×4 |
|||||||||||||||||||||||||||||||||||||||||||
Engine |
 Model |
CA6110-125,WD615.96E,YC190Â diesel engine |
||||||||||||||||||||||||||||||||||||||||||
 Rated power(HP) |
180,266,190 |
|||||||||||||||||||||||||||||||||||||||||||
 Speed (r/min) |
2300 |
|||||||||||||||||||||||||||||||||||||||||||
Size (L*W*H)(mm) |
10198×2490×2980 |
|||||||||||||||||||||||||||||||||||||||||||
Electric generator |
Model |
MF |
||||||||||||||||||||||||||||||||||||||||||
Rated power (kw) |
30 |
|||||||||||||||||||||||||||||||||||||||||||
Rated voltage(v) |
400 |
|||||||||||||||||||||||||||||||||||||||||||
Rated current(A) |
27 |
|||||||||||||||||||||||||||||||||||||||||||
Speed (r/min) |
1500 |
|||||||||||||||||||||||||||||||||||||||||||
Frequency(Hz) |
50 |
|||||||||||||||||||||||||||||||||||||||||||
Protection level |
IP21 |
|||||||||||||||||||||||||||||||||||||||||||
Insulation Class |
H |
|||||||||||||||||||||||||||||||||||||||||||
The b
Clips and Fasteners are most commonly categorized as flat or sheet material that is formed into simple or complicated shapes. Most often, Clips and Fasteners are manufactured using both low and high carbon steels, depending on the application. In some applications, high carbon spring steels are utilized where a spring force is required that cannot be obtained with normal spring forces. When high carbon spring steels are used for manufacturing, it is a standard requirement that the product is heat treated and quenched to a hardness level that allows the product to flex without deforming. Heat treating and oil quenching are commonly used for the hardening process, but an Austemper heat treating process is typically the best practice for eliminating heat treat deformation.
Steels most commonly used in our process for manufacturing Clips and Fasteners are either low carbon, cold rolled steel (without heat treatment), and high carbon spring steels ranging from Grade 1050 to 1095, along with Stainless Steels and precious metals such as Brass, Phosphor Bronze, and Beryllium Copper. Clips and Fasteners that we manufacture typically range in material thickness of .010″ up to .080″, with many of our prototype and short run orders ranging from these sizes. We also have the capability of manufacturing designs in a wide range of shapes and sizes. We can supply Clips and Fasteners with a variety of special finishes or coatings to your specification along with various heat treating requirements.
Clip Materials
Material
Grade
Specification
High Carbon Spring Steel Strip
1050
ASTM A682 (AISI 1050)
1065
ASTM A682 (AISI 1060)
1070
ASTM A682 (AISI 1070)
1074
ASTM A682 (AISI 1074)
Stainless Steel Strip
301
ASTM A666
302
ASTM A666
316
ASTM A582 (AISI 316)
17-7 PH
ASTM A693 (631) (AMS 5529)
Non-Ferrous Alloy Wire
Phosphor Bronze
ASTM B103
Beryllium Copper
ASTM B194
High Temperature Alloy Wire
Inconel 600
ASTM B168 (AMS 5540)
Inconel x750
AMS 5542
Low Carbon Steel
Cold Rolled Steel (CRS)
ASTM A1008 (AISI 1008/1010)
Spring Steel Clip,Stainless Steel Clip,Spring Clip,Stainless Clips Nanpi Jian Tong Hardware Manufacturing Co., Ltd. , https://www.sheetmetals.nl | ||||||||||||||||||||||||||||||||||||||||||||